 |
| Quantity: | |
|---|---|
18"-60" HYDRAULIC ROLL GROOVING MACHINE(TWG-8A)
TWG-8A hydraulic roll grooving machine can be groove the max. diameter of the steel pipe is 60inch. The entire groove process is automated. It equipped with automatic hydraulic system, automatic feed and automatic reset.
Product Introduction
● TWG-8A hydraulic roll grooving machine is designed for grooving 18"-60" steel pipe.
● Automatic hydraulic system, automatic feed, automatic reset through the entire process which will increase working efficiency.
● With solid and adjustable base, can adjust the height according to pipe size in order to get different center height, very suitable for grooving large diameter pipe.
Specifications
● Capacity: 18“-60"( Φ 457- Φ 1524) steel pipe.
● Max. wall thickness: 12mm.
● Output RPM: 15rpm.
● G. W: 1300kgs.
● Packaging size: 240x100x273(cm).
Standard Equipment | ||
*For SCH40 steel pipe | ||
Art. No. | Description | N.W(kgs) |
03.01.18.003 | AGS knurl wheel 50”-60” | 12.7kgs |
13.01.18.002 | AGS knurl wheel 40”-48” | 12.7kgs |
03.01.18.001 | AGS knurl wheel 26”-38” | 12.7kgs |
03.01.18.008 | AGS pinch roller 50”-60” | 6.3kgs |
03.01.18.007 | AGS pinch roller 40”-48” | 6.3kgs |
03.01.18.006 | AGS pinch roller 26”-38” | 6.3kgs |
Motor Parameter | ||
Phase | Voltage | Frequency |
Three Phase | 220/380/ 415/ 440V | 50/60 Hz |
Troubleshooting
Situation | Cause | Solution |
Pipe could not groove. | The surface of Down-wheel is rusty or dirty. | Cleaning. |
There are dirty or rusty inside pipe. | Cleaning. | |
Down-wheel wear and tear. | Replace | |
Power cut off. | Reset switch or Replace fuse. | |
There is a sound When every circle. | Weld line on pipe. | Sanding weld line on the pipe around 200mm from the end of pipe. |
There is an echo during processing. | The end of pipe is not smooth or grooving not vertically. | Sanding the end or groove pipe again. |
Over rubbing between pipe and Down-wheel. | Put wax. | |
Supporters are not in the right positions. | Adjusting, refer to user’s manual. | |
Flare over size. | Supporters stand higher. | Adjusting. |
Guide-wheel push pipe hard makes pipe deviate center. | Make Guide-wheel back but still touch pipe | |
Feeding faster. | Adjusting flow-valve | |
Grooving could not be down. | Not enough Hydraulic oil. | Adding |
Lower Working pressure. | Adjusting overflow-valve, refer to user’s manual. | |
Groove not in right size. | Not adjust depth-adjuster well. | Adjusting, refer to user’s manual. |
Our Service
1. We have established worldwide network to guarantee our timely response for your any demand no matter where are you.
2. We welcome engineers from your side to learn the technical design and normal maintenance here, this will help your easy in understanding and helpful if you need to be our dealer.
3. However, don't worry, we have our company own CD/Manual to show you along with the machine. So you can learn this from the existing documents to deepen your knowledge and understanding.
4. Anyhow there are another way is through internet video face to face for machine teaching, because of the high development in internet, the world has become smaller and you can easy contact us if any assistance needed.
5. Through all the ways, we will guarantee the service quality and ensure you will be well helped anytime anywhere.
18"-60" HYDRAULIC ROLL GROOVING MACHINE(TWG-8A)
TWG-8A hydraulic roll grooving machine can be groove the max. diameter of the steel pipe is 60inch. The entire groove process is automated. It equipped with automatic hydraulic system, automatic feed and automatic reset.
Product Introduction
● TWG-8A hydraulic roll grooving machine is designed for grooving 18"-60" steel pipe.
● Automatic hydraulic system, automatic feed, automatic reset through the entire process which will increase working efficiency.
● With solid and adjustable base, can adjust the height according to pipe size in order to get different center height, very suitable for grooving large diameter pipe.
Specifications
● Capacity: 18“-60"( Φ 457- Φ 1524) steel pipe.
● Max. wall thickness: 12mm.
● Output RPM: 15rpm.
● G. W: 1300kgs.
● Packaging size: 240x100x273(cm).
Standard Equipment | ||
*For SCH40 steel pipe | ||
Art. No. | Description | N.W(kgs) |
03.01.18.003 | AGS knurl wheel 50”-60” | 12.7kgs |
13.01.18.002 | AGS knurl wheel 40”-48” | 12.7kgs |
03.01.18.001 | AGS knurl wheel 26”-38” | 12.7kgs |
03.01.18.008 | AGS pinch roller 50”-60” | 6.3kgs |
03.01.18.007 | AGS pinch roller 40”-48” | 6.3kgs |
03.01.18.006 | AGS pinch roller 26”-38” | 6.3kgs |
Motor Parameter | ||
Phase | Voltage | Frequency |
Three Phase | 220/380/ 415/ 440V | 50/60 Hz |
Troubleshooting
Situation | Cause | Solution |
Pipe could not groove. | The surface of Down-wheel is rusty or dirty. | Cleaning. |
There are dirty or rusty inside pipe. | Cleaning. | |
Down-wheel wear and tear. | Replace | |
Power cut off. | Reset switch or Replace fuse. | |
There is a sound When every circle. | Weld line on pipe. | Sanding weld line on the pipe around 200mm from the end of pipe. |
There is an echo during processing. | The end of pipe is not smooth or grooving not vertically. | Sanding the end or groove pipe again. |
Over rubbing between pipe and Down-wheel. | Put wax. | |
Supporters are not in the right positions. | Adjusting, refer to user’s manual. | |
Flare over size. | Supporters stand higher. | Adjusting. |
Guide-wheel push pipe hard makes pipe deviate center. | Make Guide-wheel back but still touch pipe | |
Feeding faster. | Adjusting flow-valve | |
Grooving could not be down. | Not enough Hydraulic oil. | Adding |
Lower Working pressure. | Adjusting overflow-valve, refer to user’s manual. | |
Groove not in right size. | Not adjust depth-adjuster well. | Adjusting, refer to user’s manual. |
Our Service
1. We have established worldwide network to guarantee our timely response for your any demand no matter where are you.
2. We welcome engineers from your side to learn the technical design and normal maintenance here, this will help your easy in understanding and helpful if you need to be our dealer.
3. However, don't worry, we have our company own CD/Manual to show you along with the machine. So you can learn this from the existing documents to deepen your knowledge and understanding.
4. Anyhow there are another way is through internet video face to face for machine teaching, because of the high development in internet, the world has become smaller and you can easy contact us if any assistance needed.
5. Through all the ways, we will guarantee the service quality and ensure you will be well helped anytime anywhere.
